Blueprint

hackbar

its a hackpad shaped like a bar

Created by danny danny 🚀

Hackpad

36 views

0 followers

alexren alexren ⚡🚀 approved hackbar ago

Tickets awarded: 64 tickets

Tier: 5

the leds look great!

danny danny 🚀 submitted hackbar for ship review ago

danny danny 🚀 added to the journal ago

Switching from KMK to QMK

I spent a whole hour trying to build and flash my kmk code onto my board. For some reason, there always was a problem with definitions missing or just strange errors that I can't solve. I tried downloading various things like the kmk_firmware and kmkpython (a fork of circuitpython????) which both failed.

Instead, I switched to the next best thing which was QMK. By using QMK MSYS, it automatically setup my dev environment which I easily edited and compiled .uf2 files that I could drag onto my board.

image

I finally got everything working!

danny danny 🚀 added to the journal ago

Finding the Problem

image

Turns out, It wasn't my cable or my bad soldering, but my footprint being wrong. For some reason, the pads were on the wrong side and were indicated wrong with the silkscreen triangle

image
(you can see in the image, the pad on the triangle is set as 5v, but the datasheet says its ground)

In the end, I was able to desolder everything (with a hotplate this time) and flip all my components 180 degrees to fix it.
image

danny danny 🚀 added to the journal ago

Soldering Everything

I started soldering smd components first as they're pretty small.

image

It took quite some time as i decided to use a soldering iron instead of a hot plate.

I then put on the encoder as it will be then covered by the xiao rp2040

image

image

After powering it on... nothing?

I checked with a multimeter to see if i soldered everything correctly and didn't bridge anything, as well as made sure I used a good cable.

m0.hid m0.hid âš¡ approved hackbar ago

Great work on this hackpad!

danny danny 🚀 submitted hackbar for ship review ago

Shadow Shadow requested changes for hackbar ago

Hey! cool project but a few things, your PCB exceeds the limit of 100 by 100 mm, please change that! Also you are using hotswap sockets which aren't provided in the kit, Will you be sourcing them yourself?

danny danny 🚀 submitted hackbar for ship review ago

danny danny 🚀 started hackbar ago

3/9/2026 12:40 PM - Soldering Everything

I started soldering smd components first as they're pretty small.

image

It took quite some time as i decided to use a soldering iron instead of a hot plate.

I then put on the encoder as it will be then covered by the xiao rp2040

image

image

After powering it on... nothing?

I checked with a multimeter to see if i soldered everything correctly and didn't bridge anything, as well as made sure I used a good cable.

3/9/2026 12:43 PM - Finding the Problem

image

Turns out, It wasn't my cable or my bad soldering, but my footprint being wrong. For some reason, the pads were on the wrong side and were indicated wrong with the silkscreen triangle

image
(you can see in the image, the pad on the triangle is set as 5v, but the datasheet says its ground)

In the end, I was able to desolder everything (with a hotplate this time) and flip all my components 180 degrees to fix it.
image

3/10/2026 - Switching from KMK to QMK

I spent a whole hour trying to build and flash my kmk code onto my board. For some reason, there always was a problem with definitions missing or just strange errors that I can't solve. I tried downloading various things like the kmk_firmware and kmkpython (a fork of circuitpython????) which both failed.

Instead, I switched to the next best thing which was QMK. By using QMK MSYS, it automatically setup my dev environment which I easily edited and compiled .uf2 files that I could drag onto my board.

image

I finally got everything working!