Necklace
I want a 3D model of the necklace I’m going to make in jewelry, just something that shows what it’ll look like before I actually build it. and also shows me the shapes ill have to cut out.
Created by
Blake Mangum
Tier 5
31 views
0 followers
alexren ⚡🚀
approved Necklace ago
Tickets awarded: 40 tickets
Tier: 5
Pretty cool project! I really like the paper sketches at the start
CAN ⚡🚀
submitted Necklace for ship review ago
Blake Mangum
submitted Necklace for ship review ago
Blake Mangum
added to the journal ago
finished design and tried to print it
i finished up the 3d design and tried to print it out with normal settings 0.2 mm but it was to precise of a thing that it needs to be 0.10-0.15 mm to get the level of detail. so that was pretty annoying but i reprinted it with finer detail. and it looks pretty good. i have jewlery tomorrow so i hope im able to make most of the real one made.
Blake Mangum
added to the journal ago
modeled the necklace one as a full an the three sections
it was easy to make the main oval? idk what shape that would be called. it got a lot harder when i was trying to make all of the curved mountains they were hard to get all of them to be the right shape had to edit them a lot more than i thought i would have to. also the reason for the hole on the top is to easily center the bezel with the stone.
Blake Mangum
added to the journal ago
started to think about how to design this in fusion 360
this necklace will be in tiers/overlays the part with the sun (a set stone) on the bottom and then layers going up like that. each layer will be around 1-2 mm thick. making it in total just with the layers not including the stone about 3-6 mm thick. it should also be like 30 X 15 mm with the two ends rounded. so those are my dimensions taken care of. here is a very basic size estimated picture.
Blake Mangum
added to the journal ago
Started to think about what it should look like Size & Shape
i found a shirt that i thought had a cool design that would work well for a necklace. i like the mountains and the sun but not really the wave so in some of the brainstorming size and actual shape i removed it.
Blake Mangum
started Necklace ago
12/2/2025 6:22 PM - Started to think about what it should look like Size & Shape
i found a shirt that i thought had a cool design that would work well for a necklace. i like the mountains and the sun but not really the wave so in some of the brainstorming size and actual shape i removed it.
12/2/2025 6:47 PM - started to think about how to design this in fusion 360
this necklace will be in tiers/overlays the part with the sun (a set stone) on the bottom and then layers going up like that. each layer will be around 1-2 mm thick. making it in total just with the layers not including the stone about 3-6 mm thick. it should also be like 30 X 15 mm with the two ends rounded. so those are my dimensions taken care of. here is a very basic size estimated picture.
12/2/2025 9 PM - modeled the necklace one as a full an the three sections
it was easy to make the main oval? idk what shape that would be called. it got a lot harder when i was trying to make all of the curved mountains they were hard to get all of them to be the right shape had to edit them a lot more than i thought i would have to. also the reason for the hole on the top is to easily center the bezel with the stone.
12/2/2025 11 PM - finished design and tried to print it
i finished up the 3d design and tried to print it out with normal settings 0.2 mm but it was to precise of a thing that it needs to be 0.10-0.15 mm to get the level of detail. so that was pretty annoying but i reprinted it with finer detail. and it looks pretty good. i have jewlery tomorrow so i hope im able to make most of the real one made.