2/11/2026 3 AM - i make first schemat for keyboard 65% + f1 -> f12

i make a first prototype of schemat of keyboard 65% + f1 -> f12 i use redragon keyabord for keycaps layout at schematic
bla bla bla bla bla i neeeeed to fill min characters

2/11/2026 4 AM - ending schemat idk look good

i add global labels to keyboard look more clean.

global labels look this to conect for with mcu motherboard

and i make argb leds

now i go setup footprint

2/12/2026 - footprint and some changes

i set footprint and i give change something in schematic.

i use

cherry mx swithc footprint

diode smd

1x25 1.00mm pin coneector

i need change only resistor and led. i think i to need do some bigger diode

uh i add 4 more sw_push only for stabilizer

i name it switch to

2/13/2026 1 PM - replace diods

i use 1N4148W becus im dumb andi give normal diod befor
i delate all diod and replace it

with 1N4148W diod bruh
i use sod-123

i didt use 1N4148 becus i dont have footprint of it

there its all after place

2/13/2026 4 PM - footprint segregate

i segregate footprint becuse its be easy connect later

i only dont give diod becuse its small so its be hard to segragete now.

sorry i give old photo what look like befor segregate

now it look like this segregate this took me around 2h

2/13/2026 5 PM - keyboard footprint - switch

half of this ready

look good its take me around 20minus idk its me 0.4h i dont know

im after half of keyboard ehh next 30 minuts

i think i will end all in around 1h

now diods ehhhh
8 minuts later i end that

2/13/2026 6 PM - placing diodes

i place all diodes it start looking like keyboard leds left and pins. mhm and conectiong i use stoper to watch time

i need fill min characters aaaaaaa

2/13/2026 9 PM - routing a pcb of keyboard

i do first conection on all swtich

now i conect swtich to diods

i make mistake and i need make new versio

i do agein conectins from swtich do diods

i make conection swtich_matrix to pins

i make conections to row gnd from swtich to matrix

i do conection to matrix

i end making conections

2/22/2026 12:14 AM - start of mcu

i start making keyboard mcu first i do conections to switch pcb base on conections what i made on keyboard pcb and schemat
bla bla bla its neeeed bee filled

2/22/2026 12:39 AM - usb nad step_up

i use ucb c port to all power go to diod but this take some ov voltage i need stable 5v so i give it to go , to step up module what give clean v5 ....

i use this cool schmeat from
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/196/4012002220_2D004753D358_IC_5B00_MT3608_2C00_SMD_2C00_SOT23_2D00_6L_2C00_AEROSEMI_5D00_.pdf

there its end verion of it module

2/22/2026 2 AM - rp2040

i do something like this idk its be work. i use little help from dev board tutorial becus i cant find how to conect it

and i need change schemat little bit becus this what i have befor dont give me clean look

and there its litle power-down base on ams1117

2/22/2026 4 PM - rp2040 controler

i make this idk what is name for

i change diod on power from usb input becus i need 2 ampers for leds this diod what i use befor give up on 15 argb leds

i do this more cleean

2/22/2026 5 PM - idk what its this

reset this repeir to keyboard dont reseting non stop

i ad 27 Ohmmmmm Resistors to d+ d- from usb

i make and change this 1.1v module

i make same for 3.3v mcu
i like this :)

2/22/2026 6 PM - power problem

i making reserch on slack and reddit all its good. everyone say me this ams what i use befor heat up so much so i change to ADP232121312321321 idk 3.3 you see name

around 1h i speend only to reserching power is good :<

this adj its sensor what checking its a 3.3v

2/22/2026 7 PM - Super Flash memory and something else

i make a flash memory for rp2040 you see what comepoemnt

i make this. this its to debug mcu when something go wronng ble ble ble ble ble ble bel ble ble

2/22/2026 8 PM - Super Flash memory and something else

i make a flash memory for rp2040 you see what comepoemnt

i make this. this its to debug mcu when something go wronng ble ble ble ble ble ble bel ble ble

2/22/2026 9 PM - start a battery system power

i start making battery power system with this

clear 5v go to battery but after battery it cant back to it
im ending this at that moment im upgrade that later

sry but batteri managmante its complicated

2/23/2026 - Motherboard Prototype - V1

i make first prototype of mcu motherboard i can say its look bad for me personal i dont wanna use this for end version becus i wanna add something what i dont have it make this all take me around 40minut becus i be testing diffrent conections

3/14/2026 6 PM - Complication

14 days left to end of blueprint so i will use rp 2040. ehh i spend over 10h on mcu what i dont use. but by this change project cost so much less. ehh i dont say i lost that time. i teach so much at making mcu motherboard. i save it schmeat for another project later

its photo how it look like but i dont use it . i very sorry :(

3/14/2026 8 PM - new verison without leds

i just delet it
a start doing repo to

like no leds version is for poeple who no need it. and for me personal soldring leds complicated this project i think about change diods

3/21/2026 - i need change

i need edit orginl pcb ehhhh

i there need deleate all and change all pins by non changing schmeat to one pin conectors
its not be hard but it take so long

is how it look

3/23/2026 - Reserch for parts + case

im doing reserch for all left parts. it take way long what i give there i think i spend around 5h finding all parts. maybe i pick this anime XD but is not cheap and dont have function keycaps

for now is this parts but i wanna change some of it i to make simple case . BYE i go sleep

3/27/2026 1 AM - Pass test and add more version of case

i pass this test on github i spend aorud 7h on working on github test (ai repo test) and finnaly im pass . i making is for oanly one resson , i wanna to get aproved at first time . pls revivers.

and i add some stl file but is name like step.stl idk bambu slicer is bugged

it perfect fit in a1 plate

3/27/2026 2 AM - This what show it be fit

i make it in tinkercad becuse dumb Fusion dont let me inport pcb file from kicad. i know i know its better to be iin step file but bro. if progogram dont let me do this?

3/27/2026 11 PM - i make asslembly

simple visuailation. of asslembly

i dont know why this is glass i need fill that bruh
what i need say. i like cats. this is only 0.1H bro give me live i dont wanna write 150 characters