Blueprint

Ultisense

an esp32-s3 devboard made to sense as many things as possible has: - an NFC antenna - 6DOF IMU - VOC air sensor - humidity & temperature sensor - color & ambient light sensor - magnetometer it additionally has: - microphone - two speakers - microSD card

Created by darsh darsh 🚀

Tier 3

28 views

0 followers

cubit010 cubit010 âš¡ approved Ultisense ago

Tickets awarded: 33 tickets

Tier: 3

looks great!
really like how many features you packed into the board

darsh darsh 🚀 submitted Ultisense for ship review ago

darsh darsh 🚀 added to the journal ago

made it work!!!

i initially tried this the second it shipped but it didnt work for some reason; i thought i messed up in the i2c wiring because all three sensors i tried out from the beginning refused to give me any data. i then asked for help in 1bitsquared which is a goated community, who pointed me into using a logic analyzer which i conveniently had stashed away from a random aliexpress order many months ago. soldered the headers on and connected it to view the data, and instead found that miraculously it had started working, and after troubleshooting a lot with the board type in arduino because it would refuse to compile otherwise, i got it actually working from the code (also made a custom board for the board manager of the ide). then adapted the gpt code into the library code, and got a voc index reading by using the sensiron algorithm (note that it takes a while to warm up the sensor before getting real readings), and now it gives accurate data!! hovers around 90-120 VOC Index in my room, and when i breathe on it it spikes up to like 200 which is exactly what its supposed to be doing which is goated !! will test the other sensors later, and figure out how logic analyzer actually works

IMG_3321

Screenshot 2026-02-10 231431

BUILD

iamalive iamalive 🚀 approved Ultisense ago

Tier approved: 3

Grant approved: $103.00

Looks good!

darsh darsh 🚀 submitted Ultisense for ship review ago

iamalive iamalive 🚀 requested changes for Ultisense ago

Please also add the pcbs and their prices to your bom!

darsh darsh 🚀 submitted Ultisense for ship review ago

iamalive iamalive 🚀 requested changes for Ultisense ago

Please include a BOM.csv in your repo!

darsh darsh 🚀 submitted Ultisense for ship review ago

technical_. technical_. requested changes for Ultisense ago

Since this is a devboard with many components, code is required. This can be simply just to test if everything on your board works, sort of a validation check. In addition your BOM.CSV file should be updated with the same information from the excel file. We cannot view the contents of Excel files unless we manually download it, which can make it inaccessible for some users.

darsh darsh 🚀 submitted Ultisense for ship review ago

iamalive iamalive 🚀 requested changes for Ultisense ago

Please include a screenshot of the shipping option you've chosen, as we need to verify what option you've done is the cheapest! (Usually global standard direct)

darsh darsh 🚀 submitted Ultisense for ship review ago

darsh darsh 🚀 added to the journal ago

fixed nfc

completely forgot about the gnd place oops. also apparently no traces are allowed to cross the coil at all, contrary to what i read of some straight ones being allowed. so fixed the nfc antenna issues, removed capacitive touch because there's no space to put it anywhere, and also cleaned some things. moved the oled to a different spot, and now have a lot of space on my board but unfortunately not enough to actually make the board smaller. also added some test points in case i need them

Screenshot 2025-12-01 205433

technical_. technical_. requested changes for Ultisense ago

This does not have enough hardware complexity to warrant a tier two. I understand that this involved many components, but this is really just maxing the amount of peripherals you can connect to the S3.
In addition, please organize your repo. You have files everywhere, and they can be grouped up into folders.

darsh darsh 🚀 submitted Ultisense for ship review ago

koeg koeg 🚀 requested changes for Ultisense ago

Hi! Really cool project!!!! You don't have any test points on your PCB, this will make debugging very hard, if you messed something up. I recommend you to add some test points and isolation jumpers. If you are really confident in your design, you can resubmit, but I highly recommend test points

This is a great video: https://youtu.be/hkSad4n76Lc?si=MjNV5wcAhnA35uM0

darsh darsh 🚀 submitted Ultisense for ship review ago

Shaurya Bisht Shaurya Bisht requested changes for Ultisense ago

The cart screenshot needs to have the product you are buying inside the screenshot. I think it would be on the screen before you pay.

darsh darsh 🚀 added to the journal ago

banner

--------------------------------------------------------------------banner---------------------------------------------------------------------------:

banner

darsh darsh 🚀 submitted Ultisense for ship review ago

darsh darsh 🚀 added to the journal ago

done !!

added silkscreen, fixed the jlcpcb BOM and placements; the cost ended up being literally $199.99 which is kinda cooked, pcb assembly is so expensive especially since all the sensors are extended, and i cant get the cheap shipping because the pcba is more than $99.

image

image

darsh darsh 🚀 added to the journal ago

routing done!!

finally finished routing, also added the gnd pour and stitching vias. it actually wasnt that bad, the process i did this time with grouping sections together and making a layout, and additionally giving myself some space definitely made it miles more pleasant to do. definitely couldve made this board smaller but its not like that matters for me with this board so oh well.

image

darsh darsh 🚀 added to the journal ago

pcb layout done and grouped

layout done and everything is now grouped and the within groups are routed. i need to route the full board now, might be terrible because i tried to minimize spacing; but hopefully it wont be like impossible. might get rid of the oled screen for just being unnecessary.

image

image

darsh darsh 🚀 added to the journal ago

routing

design considerations i must follow:

  • usb c at one edge
  • esp32s3 antenna at other edge
  • sd card on side edge
  • headers on other side edge
  • very minimal traces through nfc antenna
  • battery connection at side edge
  • two speakers; one on each edge
  • microphone in middle
  • imu in middle
  • touch pad at edge partial routing: image

darsh darsh 🚀 added to the journal ago

added a few more sensors

added temperature, humidity, color/lux sensor, magnetometer. not much more to say but im officially for real done with the schematic. i also figured out the nfc antenna, hopefully my numbers are correct.

Screenshot 2025-11-24 220844
Screenshot 2025-11-24 193259
image

darsh darsh 🚀 added to the journal ago

finished schematic fully and starting pcb

went back and forth on multiple things so this took way longer than it really needed to, since i also researched and designed like 4 things i ended up just deleting. initially i was going to just use modules for both capacitive touch and nfc because they're kind of a hassle but after seeing the size and how conflicting they would look on the pcb anyways, i decided to just have both. theyll probably both be less reliable (especially the touch sensor since im using the esp32s3 gpio which isnt even certified but oh well. new schematic:

image

new pcb:
image

i have to keep in mind all the keepout for the different components, and the size of the power traces, and routing everything properly.

darsh darsh 🚀 added to the journal ago

finished schematic

finished schematic; adding footprints now
found a tool called easyeda2kicad that lets me download the jlc parts footprints which makes it a lot more convenient and wouldve saved me time in creating footprints

image

darsh darsh 🚀 added to the journal ago

audio path

added the audio path !!
it goes from the pcm DAC, to the pamb403 amplifier, to the 2 l, r speakers which will be 8ohm
also added a microphone that im planning to use for basic commands
misc fixes: added an ntc thermistor, pull ups to the sda/scl

image

darsh darsh 🚀 added to the journal ago

mcu + multiplexer + sd card

added mcu buttons and multiplexer (using mcp23017 bc other one is analog), and also wired the sd card. thats it basically; using i2c for multiplexer and spi for sd card

image

darsh darsh 🚀 added to the journal ago

added power path

added all of my power path stuff
flow:
usb 2.0
data goes through esd protection, to mcu data
vbus goes to BQ24075 which charges at 500mA and has two leds for status, outputs usb if connected otherwise battery
output goes to TPS61023, 5v boost to 5v rail
also goes to an ldo which outputs to 3v3 rail

image

darsh darsh 🚀 added to the journal ago

bom

-esp32-s3-wroom MCU
-CP2102 UART chip
-GY-87 IMU
-TTP223 touch sensor
-LM75A temperature sensor
-MSM261DGT003 microphone
-HC-SR04 ultrasonic sensor
-OV5640 camera
-TS-1088-AR02016 buttons
-SSD1306 OLED screen

audio:
-PAM8403 amplifier
-8ohm 1W speaker

led: KT-0603R
sd: TF PUSH
nfc: PN532 module
multiplexer: CD4051BM96

power:
-TYPE-C-31-M-12
-BQ24075 charger
-2 pin jst housing (for batt)
-AP2112K-3.3 3v3 LDO
-TPS61023DRLT boost converter

ultisense

darsh darsh 🚀 added to the journal ago

planning...

features i want it to have:
-esp32-s3 chip with cool working wifi/bluetooth
large

-usbc 100w power, charging to lipo battery (not actually 100w) while running off of usb power or battery, esd protection
-multiplexer
-imu
-oled screen
-temperature sensing
-touch sensor
-microphone + speaker
-espcam module
-bunch of leds
-5v output
-ir blaster
-buttons
-ultrasonic sensor
-sd card reader
-headers for 3v3, 5v, 9v, 12v

darsh darsh 🚀 started Ultisense ago

11/8/2025 6 PM - planning...

features i want it to have:
-esp32-s3 chip with cool working wifi/bluetooth
large

-usbc 100w power, charging to lipo battery (not actually 100w) while running off of usb power or battery, esd protection
-multiplexer
-imu
-oled screen
-temperature sensing
-touch sensor
-microphone + speaker
-espcam module
-bunch of leds
-5v output
-ir blaster
-buttons
-ultrasonic sensor
-sd card reader
-headers for 3v3, 5v, 9v, 12v

11/8/2025 11 PM - bom

-esp32-s3-wroom MCU
-CP2102 UART chip
-GY-87 IMU
-TTP223 touch sensor
-LM75A temperature sensor
-MSM261DGT003 microphone
-HC-SR04 ultrasonic sensor
-OV5640 camera
-TS-1088-AR02016 buttons
-SSD1306 OLED screen

audio:
-PAM8403 amplifier
-8ohm 1W speaker

led: KT-0603R
sd: TF PUSH
nfc: PN532 module
multiplexer: CD4051BM96

power:
-TYPE-C-31-M-12
-BQ24075 charger
-2 pin jst housing (for batt)
-AP2112K-3.3 3v3 LDO
-TPS61023DRLT boost converter

ultisense

11/9/2025 10 PM - added power path

added all of my power path stuff
flow:
usb 2.0
data goes through esd protection, to mcu data
vbus goes to BQ24075 which charges at 500mA and has two leds for status, outputs usb if connected otherwise battery
output goes to TPS61023, 5v boost to 5v rail
also goes to an ldo which outputs to 3v3 rail

image

11/9/2025 11 PM - mcu + multiplexer + sd card

added mcu buttons and multiplexer (using mcp23017 bc other one is analog), and also wired the sd card. thats it basically; using i2c for multiplexer and spi for sd card

image

11/10/2025 - audio path

added the audio path !!
it goes from the pcm DAC, to the pamb403 amplifier, to the 2 l, r speakers which will be 8ohm
also added a microphone that im planning to use for basic commands
misc fixes: added an ntc thermistor, pull ups to the sda/scl

image

11/11/2025 - finished schematic

finished schematic; adding footprints now
found a tool called easyeda2kicad that lets me download the jlc parts footprints which makes it a lot more convenient and wouldve saved me time in creating footprints

image

11/23/2025 - finished schematic fully and starting pcb

went back and forth on multiple things so this took way longer than it really needed to, since i also researched and designed like 4 things i ended up just deleting. initially i was going to just use modules for both capacitive touch and nfc because they're kind of a hassle but after seeing the size and how conflicting they would look on the pcb anyways, i decided to just have both. theyll probably both be less reliable (especially the touch sensor since im using the esp32s3 gpio which isnt even certified but oh well. new schematic:

image

new pcb:
image

i have to keep in mind all the keepout for the different components, and the size of the power traces, and routing everything properly.

11/24/2025 - added a few more sensors

added temperature, humidity, color/lux sensor, magnetometer. not much more to say but im officially for real done with the schematic. i also figured out the nfc antenna, hopefully my numbers are correct.

Screenshot 2025-11-24 220844
Screenshot 2025-11-24 193259
image

11/25/2025 10 AM - routing

design considerations i must follow:

  • usb c at one edge
  • esp32s3 antenna at other edge
  • sd card on side edge
  • headers on other side edge
  • very minimal traces through nfc antenna
  • battery connection at side edge
  • two speakers; one on each edge
  • microphone in middle
  • imu in middle
  • touch pad at edge partial routing: image

11/25/2025 9 PM - pcb layout done and grouped

layout done and everything is now grouped and the within groups are routed. i need to route the full board now, might be terrible because i tried to minimize spacing; but hopefully it wont be like impossible. might get rid of the oled screen for just being unnecessary.

image

image

11/28/2025 3 PM - routing done!!

finally finished routing, also added the gnd pour and stitching vias. it actually wasnt that bad, the process i did this time with grouping sections together and making a layout, and additionally giving myself some space definitely made it miles more pleasant to do. definitely couldve made this board smaller but its not like that matters for me with this board so oh well.

image

11/28/2025 6:02 PM - done !!

added silkscreen, fixed the jlcpcb BOM and placements; the cost ended up being literally $199.99 which is kinda cooked, pcb assembly is so expensive especially since all the sensors are extended, and i cant get the cheap shipping because the pcba is more than $99.

image

image

11/28/2025 6:46 PM - banner

--------------------------------------------------------------------banner---------------------------------------------------------------------------:

banner

12/1/2025 - fixed nfc

completely forgot about the gnd place oops. also apparently no traces are allowed to cross the coil at all, contrary to what i read of some straight ones being allowed. so fixed the nfc antenna issues, removed capacitive touch because there's no space to put it anywhere, and also cleaned some things. moved the oled to a different spot, and now have a lot of space on my board but unfortunately not enough to actually make the board smaller. also added some test points in case i need them

Screenshot 2025-12-01 205433

2/10/2026 - made it work!!!

i initially tried this the second it shipped but it didnt work for some reason; i thought i messed up in the i2c wiring because all three sensors i tried out from the beginning refused to give me any data. i then asked for help in 1bitsquared which is a goated community, who pointed me into using a logic analyzer which i conveniently had stashed away from a random aliexpress order many months ago. soldered the headers on and connected it to view the data, and instead found that miraculously it had started working, and after troubleshooting a lot with the board type in arduino because it would refuse to compile otherwise, i got it actually working from the code (also made a custom board for the board manager of the ide). then adapted the gpt code into the library code, and got a voc index reading by using the sensiron algorithm (note that it takes a while to warm up the sensor before getting real readings), and now it gives accurate data!! hovers around 90-120 VOC Index in my room, and when i breathe on it it spikes up to like 200 which is exactly what its supposed to be doing which is goated !! will test the other sensors later, and figure out how logic analyzer actually works

IMG_3321

Screenshot 2026-02-10 231431

BUILD