Ultisense
an esp32-s3 devboard made to sense as many things as possible has: - an NFC antenna - 6DOF IMU - VOC air sensor - humidity & temperature sensor - color & ambient light sensor - magnetometer it additionally has: - microphone - two speakers - microSD card
Created by
darsh 🚀
Tier 3
28 views
0 followers
cubit010 âš¡
approved Ultisense ago
Tickets awarded: 33 tickets
Tier: 3
looks great!
really like how many features you packed into the board
darsh 🚀
submitted Ultisense for ship review ago
darsh 🚀
added to the journal ago
made it work!!!
i initially tried this the second it shipped but it didnt work for some reason; i thought i messed up in the i2c wiring because all three sensors i tried out from the beginning refused to give me any data. i then asked for help in 1bitsquared which is a goated community, who pointed me into using a logic analyzer which i conveniently had stashed away from a random aliexpress order many months ago. soldered the headers on and connected it to view the data, and instead found that miraculously it had started working, and after troubleshooting a lot with the board type in arduino because it would refuse to compile otherwise, i got it actually working from the code (also made a custom board for the board manager of the ide). then adapted the gpt code into the library code, and got a voc index reading by using the sensiron algorithm (note that it takes a while to warm up the sensor before getting real readings), and now it gives accurate data!! hovers around 90-120 VOC Index in my room, and when i breathe on it it spikes up to like 200 which is exactly what its supposed to be doing which is goated !! will test the other sensors later, and figure out how logic analyzer actually works


iamalive 🚀
approved Ultisense ago
Tier approved: 3
Grant approved: $103.00
Looks good!
darsh 🚀
submitted Ultisense for ship review ago
iamalive 🚀
requested changes for Ultisense ago
Please also add the pcbs and their prices to your bom!
darsh 🚀
submitted Ultisense for ship review ago
iamalive 🚀
requested changes for Ultisense ago
Please include a BOM.csv in your repo!
darsh 🚀
submitted Ultisense for ship review ago
technical_.
requested changes for Ultisense ago
Since this is a devboard with many components, code is required. This can be simply just to test if everything on your board works, sort of a validation check. In addition your BOM.CSV file should be updated with the same information from the excel file. We cannot view the contents of Excel files unless we manually download it, which can make it inaccessible for some users.
darsh 🚀
submitted Ultisense for ship review ago
iamalive 🚀
requested changes for Ultisense ago
Please include a screenshot of the shipping option you've chosen, as we need to verify what option you've done is the cheapest! (Usually global standard direct)
darsh 🚀
submitted Ultisense for ship review ago
darsh 🚀
added to the journal ago
fixed nfc
completely forgot about the gnd place oops. also apparently no traces are allowed to cross the coil at all, contrary to what i read of some straight ones being allowed. so fixed the nfc antenna issues, removed capacitive touch because there's no space to put it anywhere, and also cleaned some things. moved the oled to a different spot, and now have a lot of space on my board but unfortunately not enough to actually make the board smaller. also added some test points in case i need them

technical_.
requested changes for Ultisense ago
This does not have enough hardware complexity to warrant a tier two. I understand that this involved many components, but this is really just maxing the amount of peripherals you can connect to the S3.
In addition, please organize your repo. You have files everywhere, and they can be grouped up into folders.
darsh 🚀
submitted Ultisense for ship review ago
koeg 🚀
requested changes for Ultisense ago
Hi! Really cool project!!!! You don't have any test points on your PCB, this will make debugging very hard, if you messed something up. I recommend you to add some test points and isolation jumpers. If you are really confident in your design, you can resubmit, but I highly recommend test points
This is a great video: https://youtu.be/hkSad4n76Lc?si=MjNV5wcAhnA35uM0
darsh 🚀
submitted Ultisense for ship review ago
Shaurya Bisht
requested changes for Ultisense ago
The cart screenshot needs to have the product you are buying inside the screenshot. I think it would be on the screen before you pay.
darsh 🚀
added to the journal ago
banner
--------------------------------------------------------------------banner---------------------------------------------------------------------------:

darsh 🚀
submitted Ultisense for ship review ago
darsh 🚀
added to the journal ago
done !!
added silkscreen, fixed the jlcpcb BOM and placements; the cost ended up being literally $199.99 which is kinda cooked, pcb assembly is so expensive especially since all the sensors are extended, and i cant get the cheap shipping because the pcba is more than $99.


darsh 🚀
added to the journal ago
routing done!!
finally finished routing, also added the gnd pour and stitching vias. it actually wasnt that bad, the process i did this time with grouping sections together and making a layout, and additionally giving myself some space definitely made it miles more pleasant to do. definitely couldve made this board smaller but its not like that matters for me with this board so oh well.

darsh 🚀
added to the journal ago
pcb layout done and grouped
layout done and everything is now grouped and the within groups are routed. i need to route the full board now, might be terrible because i tried to minimize spacing; but hopefully it wont be like impossible. might get rid of the oled screen for just being unnecessary.


darsh 🚀
added to the journal ago
routing
design considerations i must follow:
- usb c at one edge
- esp32s3 antenna at other edge
- sd card on side edge
- headers on other side edge
- very minimal traces through nfc antenna
- battery connection at side edge
- two speakers; one on each edge
- microphone in middle
- imu in middle
- touch pad at edge
partial routing:
darsh 🚀
added to the journal ago
added a few more sensors
added temperature, humidity, color/lux sensor, magnetometer. not much more to say but im officially for real done with the schematic. i also figured out the nfc antenna, hopefully my numbers are correct.



darsh 🚀
added to the journal ago
finished schematic fully and starting pcb
went back and forth on multiple things so this took way longer than it really needed to, since i also researched and designed like 4 things i ended up just deleting. initially i was going to just use modules for both capacitive touch and nfc because they're kind of a hassle but after seeing the size and how conflicting they would look on the pcb anyways, i decided to just have both. theyll probably both be less reliable (especially the touch sensor since im using the esp32s3 gpio which isnt even certified but oh well. new schematic:

new pcb:

i have to keep in mind all the keepout for the different components, and the size of the power traces, and routing everything properly.
darsh 🚀
added to the journal ago
finished schematic
finished schematic; adding footprints now
found a tool called easyeda2kicad that lets me download the jlc parts footprints which makes it a lot more convenient and wouldve saved me time in creating footprints

darsh 🚀
added to the journal ago
audio path
added the audio path !!
it goes from the pcm DAC, to the pamb403 amplifier, to the 2 l, r speakers which will be 8ohm
also added a microphone that im planning to use for basic commands
misc fixes: added an ntc thermistor, pull ups to the sda/scl

darsh 🚀
added to the journal ago
mcu + multiplexer + sd card
added mcu buttons and multiplexer (using mcp23017 bc other one is analog), and also wired the sd card. thats it basically; using i2c for multiplexer and spi for sd card

darsh 🚀
added to the journal ago
added power path
added all of my power path stuff
flow:
usb 2.0
data goes through esd protection, to mcu data
vbus goes to BQ24075 which charges at 500mA and has two leds for status, outputs usb if connected otherwise battery
output goes to TPS61023, 5v boost to 5v rail
also goes to an ldo which outputs to 3v3 rail

darsh 🚀
added to the journal ago
bom
-esp32-s3-wroom MCU
-CP2102 UART chip
-GY-87 IMU
-TTP223 touch sensor
-LM75A temperature sensor
-MSM261DGT003 microphone
-HC-SR04 ultrasonic sensor
-OV5640 camera
-TS-1088-AR02016 buttons
-SSD1306 OLED screen
audio:
-PAM8403 amplifier
-8ohm 1W speaker
led: KT-0603R
sd: TF PUSH
nfc: PN532 module
multiplexer: CD4051BM96
power:
-TYPE-C-31-M-12
-BQ24075 charger
-2 pin jst housing (for batt)
-AP2112K-3.3 3v3 LDO
-TPS61023DRLT boost converter

darsh 🚀
added to the journal ago
planning...
features i want it to have:
-esp32-s3 chip with cool working wifi/bluetooth
-usbc 100w power, charging to lipo battery (not actually 100w) while running off of usb power or battery, esd protection
-multiplexer
-imu
-oled screen
-temperature sensing
-touch sensor
-microphone + speaker
-espcam module
-bunch of leds
-5v output
-ir blaster
-buttons
-ultrasonic sensor
-sd card reader
-headers for 3v3, 5v, 9v, 12v
darsh 🚀
started Ultisense ago
11/8/2025 6 PM - planning...
features i want it to have:
-esp32-s3 chip with cool working wifi/bluetooth
-usbc 100w power, charging to lipo battery (not actually 100w) while running off of usb power or battery, esd protection
-multiplexer
-imu
-oled screen
-temperature sensing
-touch sensor
-microphone + speaker
-espcam module
-bunch of leds
-5v output
-ir blaster
-buttons
-ultrasonic sensor
-sd card reader
-headers for 3v3, 5v, 9v, 12v
11/8/2025 11 PM - bom
-esp32-s3-wroom MCU
-CP2102 UART chip
-GY-87 IMU
-TTP223 touch sensor
-LM75A temperature sensor
-MSM261DGT003 microphone
-HC-SR04 ultrasonic sensor
-OV5640 camera
-TS-1088-AR02016 buttons
-SSD1306 OLED screen
audio:
-PAM8403 amplifier
-8ohm 1W speaker
led: KT-0603R
sd: TF PUSH
nfc: PN532 module
multiplexer: CD4051BM96
power:
-TYPE-C-31-M-12
-BQ24075 charger
-2 pin jst housing (for batt)
-AP2112K-3.3 3v3 LDO
-TPS61023DRLT boost converter

11/9/2025 10 PM - added power path
added all of my power path stuff
flow:
usb 2.0
data goes through esd protection, to mcu data
vbus goes to BQ24075 which charges at 500mA and has two leds for status, outputs usb if connected otherwise battery
output goes to TPS61023, 5v boost to 5v rail
also goes to an ldo which outputs to 3v3 rail

11/9/2025 11 PM - mcu + multiplexer + sd card
added mcu buttons and multiplexer (using mcp23017 bc other one is analog), and also wired the sd card. thats it basically; using i2c for multiplexer and spi for sd card

11/10/2025 - audio path
added the audio path !!
it goes from the pcm DAC, to the pamb403 amplifier, to the 2 l, r speakers which will be 8ohm
also added a microphone that im planning to use for basic commands
misc fixes: added an ntc thermistor, pull ups to the sda/scl

11/11/2025 - finished schematic
finished schematic; adding footprints now
found a tool called easyeda2kicad that lets me download the jlc parts footprints which makes it a lot more convenient and wouldve saved me time in creating footprints

11/23/2025 - finished schematic fully and starting pcb
went back and forth on multiple things so this took way longer than it really needed to, since i also researched and designed like 4 things i ended up just deleting. initially i was going to just use modules for both capacitive touch and nfc because they're kind of a hassle but after seeing the size and how conflicting they would look on the pcb anyways, i decided to just have both. theyll probably both be less reliable (especially the touch sensor since im using the esp32s3 gpio which isnt even certified but oh well. new schematic:

new pcb:

i have to keep in mind all the keepout for the different components, and the size of the power traces, and routing everything properly.
11/24/2025 - added a few more sensors
added temperature, humidity, color/lux sensor, magnetometer. not much more to say but im officially for real done with the schematic. i also figured out the nfc antenna, hopefully my numbers are correct.



11/25/2025 10 AM - routing
design considerations i must follow:
- usb c at one edge
- esp32s3 antenna at other edge
- sd card on side edge
- headers on other side edge
- very minimal traces through nfc antenna
- battery connection at side edge
- two speakers; one on each edge
- microphone in middle
- imu in middle
- touch pad at edge
partial routing:
11/25/2025 9 PM - pcb layout done and grouped
layout done and everything is now grouped and the within groups are routed. i need to route the full board now, might be terrible because i tried to minimize spacing; but hopefully it wont be like impossible. might get rid of the oled screen for just being unnecessary.


11/28/2025 3 PM - routing done!!
finally finished routing, also added the gnd pour and stitching vias. it actually wasnt that bad, the process i did this time with grouping sections together and making a layout, and additionally giving myself some space definitely made it miles more pleasant to do. definitely couldve made this board smaller but its not like that matters for me with this board so oh well.

11/28/2025 6:02 PM - done !!
added silkscreen, fixed the jlcpcb BOM and placements; the cost ended up being literally $199.99 which is kinda cooked, pcb assembly is so expensive especially since all the sensors are extended, and i cant get the cheap shipping because the pcba is more than $99.


11/28/2025 6:46 PM - banner
--------------------------------------------------------------------banner---------------------------------------------------------------------------:

12/1/2025 - fixed nfc
completely forgot about the gnd place oops. also apparently no traces are allowed to cross the coil at all, contrary to what i read of some straight ones being allowed. so fixed the nfc antenna issues, removed capacitive touch because there's no space to put it anywhere, and also cleaned some things. moved the oled to a different spot, and now have a lot of space on my board but unfortunately not enough to actually make the board smaller. also added some test points in case i need them

2/10/2026 - made it work!!!
i initially tried this the second it shipped but it didnt work for some reason; i thought i messed up in the i2c wiring because all three sensors i tried out from the beginning refused to give me any data. i then asked for help in 1bitsquared which is a goated community, who pointed me into using a logic analyzer which i conveniently had stashed away from a random aliexpress order many months ago. soldered the headers on and connected it to view the data, and instead found that miraculously it had started working, and after troubleshooting a lot with the board type in arduino because it would refuse to compile otherwise, i got it actually working from the code (also made a custom board for the board manager of the ide). then adapted the gpt code into the library code, and got a voc index reading by using the sensiron algorithm (note that it takes a while to warm up the sensor before getting real readings), and now it gives accurate data!! hovers around 90-120 VOC Index in my room, and when i breathe on it it spikes up to like 200 which is exactly what its supposed to be doing which is goated !! will test the other sensors later, and figure out how logic analyzer actually works

