Blueprint

EasyRP2040

my custom rp2040 devboard :) has debug leds and a 9-DOF IMU composed of multiple 3-axis sensors

Created by darsh darsh 🚀

Tier 3

70 views

0 followers

CAN CAN ⚡🚀 approved EasyRP2040 ago

Tickets awarded: 0 tickets

Tier: 3

Nice project

darsh darsh 🚀 submitted EasyRP2040 for ship review ago

CAN CAN ⚡🚀 requested changes for EasyRP2040 ago

Please put project photos in your readme

Tier: 3

darsh darsh 🚀 submitted EasyRP2040 for ship review ago

CAN CAN ⚡🚀 approved EasyRP2040 ago

Tier approved: 3

Grant approved: $58.00

darsh darsh 🚀 submitted EasyRP2040 for ship review ago

darsh darsh 🚀 added to the journal ago

added to jlcpcb cart

took forever too but finished making the prod files and fixing everything on jlcpcb

unfortunately the imu i put is standard only, and that adds like $50, so ill buy it and place it myself since i have solder paste and a hot gun

also drew silkscreen stuff which i didnt mention; made it on excalidraw i think it looks cute :)
done yippee

Untitled-2025-10-11-1707.png

Screenshot 2025-10-11 192141.png

darsh darsh 🚀 added to the journal ago

finished routing the pcb

finished routing the pcb; took forever to fix my routing but oh well.
lessons learned:

  • do ics first
  • do capacitors after that
  • minimize vias and non gnd back signals better i have some thermal via issues but that isnt a big problem, especially single im doing pcba as well Screenshot 2025-10-11 163931.png

darsh darsh 🚀 added to the journal ago

more routing...

this takes forever aaaa
routed more of the pcb, started the gnd plane which didnt do much bc my routing was very bad, separated a whole bunch of gnd pins. need to fix a lot of routing bc i have a bunch of bottom and top traces so i cant pass gnd through it :(
Screenshot 2025-10-11 010821.png

darsh darsh 🚀 added to the journal ago

partially routed pcb

added footprints to everything, and partially routed the pcb. i have the rough shape of everything there, and roughly where everything is supposed to go. learned that you need to do differential pairs, and that the usb lines need to be the same length so that data travel at the same exact rate
Screenshot 2025-10-10 224958.png

darsh darsh 🚀 added to the journal ago

added imu + leds for customization

added the icm-20602 imu on the devboard; picked it bc its the simplest one that jlcpcb has. it requires two capacitors on vdd for some reason, and one other one on vddio. also added leds, one is a power led (will be green), one is a bootloader led which hopefully going through RUN should only be on when the devboard is in BOOTSEL, and one last one thats just connected to gpio25 bc its unused.
Screenshot 2025-10-10 190902.png

darsh darsh 🚀 added to the journal ago

finished the schamtic !

finished the schematic for the devboard

notes on learning:

  • decoupling capacitors filter out noise in power; 0.1uF for the each power pin (theres multiple in reality, kicad just merges the same ones together), and 1uF for each power line
  • shield is the metal conductive part on the usb, connects to gnd to improve EMI (electromagnetic interference)
  • 10uF bulk capacitors to filter out significant noise when 5v is stepped down to 3v3, both on input and output
  • usb dp and dm go through 27ohm resistors to prevent distortion at high data speed, called termination resistors
  • crystal oscillator: vibrating quartz crystal, amplified and fed to the MCU, this acts as a clock for all the other digital peripherals
  • important here bc using usb c; data needs to come in at very specific times
  • needs to be physically very close to the MCU
  • XIN: output from crystal to MCU
  • XOUT: output from MCU to crystal to control
  • damping resistor to XOUT for signal integrity
  • series capacitors (external load) for crystal to resonate at correct frequency
  • SPI pins: MOSI (master output), MISO (master input), SCLK (crystal oscillator timing), SS/CS (device selection, add more of these for more devices)
  • using quad SPI with this, but has 4 IO for 4x data transferring
  • needs to be connected to the dedicated hardware controller (QSPI) on the MCU
  • booting: if QSPI SS is GND when booting up, it goes into BOOTSEL, which is when it appears as a usb device
  • done by adding a pull up resistor (guarantee HIGH when booting) to 3v3, and a resistor (limit current to pin) to a button that goes to GND

Screenshot 2025-10-10 165033.png

darsh darsh 🚀 started EasyRP2040 ago

10/10/2025 4 PM - finished the schamtic !

finished the schematic for the devboard

notes on learning:

  • decoupling capacitors filter out noise in power; 0.1uF for the each power pin (theres multiple in reality, kicad just merges the same ones together), and 1uF for each power line
  • shield is the metal conductive part on the usb, connects to gnd to improve EMI (electromagnetic interference)
  • 10uF bulk capacitors to filter out significant noise when 5v is stepped down to 3v3, both on input and output
  • usb dp and dm go through 27ohm resistors to prevent distortion at high data speed, called termination resistors
  • crystal oscillator: vibrating quartz crystal, amplified and fed to the MCU, this acts as a clock for all the other digital peripherals
  • important here bc using usb c; data needs to come in at very specific times
  • needs to be physically very close to the MCU
  • XIN: output from crystal to MCU
  • XOUT: output from MCU to crystal to control
  • damping resistor to XOUT for signal integrity
  • series capacitors (external load) for crystal to resonate at correct frequency
  • SPI pins: MOSI (master output), MISO (master input), SCLK (crystal oscillator timing), SS/CS (device selection, add more of these for more devices)
  • using quad SPI with this, but has 4 IO for 4x data transferring
  • needs to be connected to the dedicated hardware controller (QSPI) on the MCU
  • booting: if QSPI SS is GND when booting up, it goes into BOOTSEL, which is when it appears as a usb device
  • done by adding a pull up resistor (guarantee HIGH when booting) to 3v3, and a resistor (limit current to pin) to a button that goes to GND

Screenshot 2025-10-10 165033.png

10/10/2025 7 PM - added imu + leds for customization

added the icm-20602 imu on the devboard; picked it bc its the simplest one that jlcpcb has. it requires two capacitors on vdd for some reason, and one other one on vddio. also added leds, one is a power led (will be green), one is a bootloader led which hopefully going through RUN should only be on when the devboard is in BOOTSEL, and one last one thats just connected to gpio25 bc its unused.
Screenshot 2025-10-10 190902.png

10/10/2025 10 PM - partially routed pcb

added footprints to everything, and partially routed the pcb. i have the rough shape of everything there, and roughly where everything is supposed to go. learned that you need to do differential pairs, and that the usb lines need to be the same length so that data travel at the same exact rate
Screenshot 2025-10-10 224958.png

10/11/2025 1 AM - more routing...

this takes forever aaaa
routed more of the pcb, started the gnd plane which didnt do much bc my routing was very bad, separated a whole bunch of gnd pins. need to fix a lot of routing bc i have a bunch of bottom and top traces so i cant pass gnd through it :(
Screenshot 2025-10-11 010821.png

10/11/2025 4 PM - finished routing the pcb

finished routing the pcb; took forever to fix my routing but oh well.
lessons learned:

  • do ics first
  • do capacitors after that
  • minimize vias and non gnd back signals better i have some thermal via issues but that isnt a big problem, especially single im doing pcba as well Screenshot 2025-10-11 163931.png

10/11/2025 7 PM - added to jlcpcb cart

took forever too but finished making the prod files and fixing everything on jlcpcb

unfortunately the imu i put is standard only, and that adds like $50, so ill buy it and place it myself since i have solder paste and a hot gun

also drew silkscreen stuff which i didnt mention; made it on excalidraw i think it looks cute :)
done yippee

Untitled-2025-10-11-1707.png

Screenshot 2025-10-11 192141.png